index

PN 02451
Lockwasher
4 Used

PN 57425
Limit Switch Cable

Four-wire cable is
six feet long and
stripped at each end.
Only used with the
obsolete metal limit
switch boxes.

PN 01043
Knob, Control Handle

PN 5089
Assembly, Power
Cord

Limit Switch Bracket
These parts are
determined by the
milling machine that
the Servo is mounted
on. Please call us for
assistance.

PN 2023-10
Assembly, Limit Switch
For type 80/140 feeds.

You get the limit switch
box with molded-in micro
switches and the limit
switch six foot cable. Unit is ready to use.

PN 00577
#6-32 x 7/8
Phillips Pan Head
Screw
Four screws required

SN 03074
#10-24 x 1-1/2
Soc. Hd. Cap
Screw

PN 5085
Assembly, Potentiometer

Assembly comes with speed
control pot, bracket, and wiring harness

PN 4894
Strain Relief

PN 5530-2
Assembly Cam

Comes with 5037
Spacer

PN 4853-12
Bottom Housing

Comes fully machined
and painted, but has
no hardware attached

PN 00555
Wavy Washer

Used at top and
bottom of armature
as necessary

PN 00703
#8-32 x 3/16
Setscrew

PN 2974
Bottom Cover

PN 00573
Brush Cap

PN 01009
5/16-24 Locknut

PN 1788
Pin, Helical Gear

PN 4737
Zytel Gear and Hub
Assembly

You can buy the Zytel
(plastic) gear by itself
under PN 4735. You
must have an arbor
press and safety
goggles to assemble.

PN 01283
Brush, Motor

PN 5744
Holder, Brush

PN 5091-2
Reversing Switch
Assembly Types
80 and 140

You will also need
to buy:
5098 Actuator and
4992 Actuator Pin

PN 5098
Actuator, Switch

PN 00982
Tolerance Ring

PN 04103
Circuit Breaker
3 Amp, Comes
with washer and
protective nut.

PN 4992
Pin, Actuator

PN 00596
3/16 x 5/8
Roll Pin

PN 03682
#10-32 x 1/4
Setscrew with
Nylon Patch

PN 5092
Rapid Switch Assembly

Contains microswitch,
mounting bracket, and
wires with pins

PN 6272
Heat Sink, Field End
Now obsolete and
not used on any
models

PN 1786-4
Assembly Motor Field
Type 80/140

PN 6271
Heat Sink, Field Side
Now obsolete and not used on any models

PN 4913
Asembly, Lift
Fork

PN 01221
Bearing, Lower
Drive Shaft

PN 02842
Washer, Spring

PN 6262-2
Nameplate, 140

PN 0266
Limit Switch Gasket

PN 1767-4
Assembly, Armature
Armature comes with
both bearings

Bearings are Part
Number 00553

PN 01241
Micro Switch,
Two required

PN 4891-2
Top Bearing Mount

Limit Switch Box
No longer avaialble

PN 03034
#8-32 X 2-3/4
Screw

PN 04761
Rivet
(Clevis Pin)

PN 5528
Spring,
Lift Fork

PN 00983
Snap Ring

PN 6225
Knob, Speed
Control

PN 4918
Assembly, Control
Handle

Does not contain
Control Handle Knob

PN 6193
Assembly, Insulator

Brass Bevel Gear
Part number depends on
which machine the Servo
feed is mounted on. Please
call us for assistance

PN 5087
Circuit Board Assembly

Circuit board assembled
and ready to use.

PN 00984
Tetra Seal
(O-Ring)

PN 3509
Upper Drive
Shaft
Assembly

PN 00982
Tolerance Ring

PN 1364
Spacer, Upper
Drive Shaft

PN 03114
#8-32 Nylon
Setscrew

PN 00502
Needle Bearing

PN 6720
Heat Sink, Bearing Mount
Now obsolete and not used
on any models.

        You can buy all the internal
        limit switch parts that usually
        go bad under part number
        W2030.
        You get the following in the
        repair kit:
        2   01241 Micro Switch
        2   1557   MS Actuators
        2   01319 Insulators
        2   01288 #2 Nuts
        4   00577 #4 Mounting Screws
        1   0266   Limit Switch Gasket

Bearing Race
Part number depends on
which machine the Servo
feed is mounted on. Please
call us for assistance

PN 03103
Mounting Grommet
for Light Pipe

PN 5064
Light Pipe

PN 4854-14
Top Housing

Top Housing comes fully machined and painted, but has no hardware parts attached.

PN 00650
Needle Bearing

PN A2499
Hex Seal Boot