150 Bkdn

PN 01043
Knob, Control Handle

PN 02451
Lockwasher
4 Used

PN 57425
Limit Switch Cable

Four-wire cable is
six feet long and
stripped at each end.
Only used with the
obsolete metal limit
switch boxes.

PN 5089
Assembly, Power
Cord

Limit Switch Bracket
These parts are
determined by the
milling machine that
the Servo is mounted
on. Please call us for
assistance.

PN 2024-7
Assembly, Limit Switch
For type 100 and 150
feeds.

You get the limit switch
box with molded-in micro
switches and the limit
switch six foot cable. Unit
is ready to use.

PN 2974
Bottom Cover

PN 01009
5/16-24 Locknut

PN 5571
Reversing Switch
Assembly Types
100 and 150

You will also need
to buy:
5098 Actuator and
4992 Actuator Pin

PN 4737
Zytel Gear and Hub
Assembly

You can buy the Zytel
(plastic) gear by itself
under PN 4735. You
must have an arbor
press and safety
goggles to assemble.

PN 00573
Brush Cap

PN 1788
Pin, Helical Gear

PN 01283
Brush, Motor

PN 4894
Strain Relief

PN 00703
#8-32 x 3/16
Setscrew

PN 00577
#6-32 x 7/8
Phillips Pan Head
Screw
Four screws required

SN 03074
#10-24 x 1-1/2
Soc. Hd. Cap
Screw

PN 5744
Holder, Brush

PN 04103
Circuit Breaker
3 Amp, Comes
with washer and
protective nut.

PN 5098
Actuator, Switch

PN 4992
Pin, Actuator

PN 5530-2
Assembly Cam

Comes with 5037
Spacer

PN 4853-12
Bottom Housing

Comes fully machined
and painted, but has
no hardware attached

PN 00555
Wavy Washer

Used at top and
bottom of armature
as necessary

PN 00982
Tolerance Ring

PN 03682
#10-32 x 1/4
Setscrew with
Nylon Patch

PN 03035
Micro Switch, Rapid

This is the PN for the
micro switch, only.

PN 00596
3/16 x 5/8
Roll Pin

PN 6272
Heat Sink, Field End
Now obsolete and
not used on any
models

PN 5568
Potentiometer and Rapid
Switch Assembly.

You get the speed control pot,
rapid switch, brackets, and
cabling--ready to use.

PN 1766-2
Assembly Motor Field
Type 100/150 Feeds

PN 6271
Heat Sink, Field Side
Now obsolete and not used on any models

PN 4913
Asembly, Lift
Fork

PN 01221
Bearing, Lower
Drive Shaft

PN 02842
Washer, Spring

PN 6262
Nameplate, Type 150

PN 6225
Knob, Speed
Control

PN 0266
Limit Switch Gasket

PN 01241
Micro Switch,
Two required

PN 1767-4
Assembly, Armature
Armature comes with
both bearings

Bearings are Part
Number 00553

PN 04761
Rivet
(Clevis Pin)

PN 5528
Spring,
Lift Fork

PN 4918
Assembly, Control
Handle

Does not contain
Control Handle Knob

Brass Bevel Gear
Part number depends on
which machine the Servo
feed is mounted on. Please
call us for assistance

PN 6193
Assembly, Insulator

PN 5567 Circuit Board Assy.
Assembled and ready to
use. For all type 150
power feeds and type 100
power feeds where all the
connections to the PC
board are plug-in.
If there are two wires going
to the PC board that are
soldered, you need a PN
5690 PC board upgrade kit.

PN 00983
Snap Ring

PN 4891-2
Top Bearing Mount

Limit Switch Box
No longer avaialble

PN 03034
#8-32 X 2-3/4
Screw

PN 00984
Tetra Seal
(O-Ring)

PN 3509
Upper Drive
Shaft
Assembly

PN 1364
Spacer, Upper
Drive Shaft

Bearing Race
Part number depends on
which machine the Servo
feed is mounted on. Please
call us for assistance

PN 03114
#8-32 Nylon
Setscrew

PN 00502
Needle Bearing

PN 00982
Tolerance Ring

PN 6720
Heat Sink, Bearing Mount
Now obsolete and not used
on any models.

        You can buy all the internal
        limit switch parts that usually
        go bad under part number
        W2030.
        You get the following in the
        repair kit:
        2   01241 Micro Switch
        2   1557   MS Actuators
        2   01319 Insulators
        2   01288 #2 Nuts
        4   00577 #4 Mounting Screws
        1   0266   Limit Switch Gasket

PN 03103
Mounting Grommet
for Light Pipe

PN 5064
Light Pipe

PN A2499
Hex Seal Boot

PN 4854-14
Top Housing

Top Housing comes fully machined and painted, but has no hardware parts attached.

PN 00650
Needle Bearing